Mechanical travel

360°×n (n： Number of turns)

Protection grade (IP)

IP40

Starting torque

Bushingmount type：≤3mN·m (30gf·cm) ；Servomount type：≤2mN·m (20gf·cm)

Stopper strength

Approx. 0.15N•m (1.5kgf•cm)

Appropriate fastening torque of the nut

≤0.8N·m (8kgf•cm)

Rotational life expectancy

25℃，No load at 40r.p.m；3 Turns ——600,000 shaft revolutions；5 Turns——1,000,000 shaft revolutions；10 Turns——2,000,000 shaft revolutions；Total resistance value variation:≤ ± 5％ against initial value； Independent Iinearity tolerance:≤ 150％ of specified value；Noise: ≤500Ω E.N.R.

Mass

Approx. 10g(Both 5-turn and 10-turn)

Operating temperature range

-55℃～+105℃

Temperature cycle

5 cycles under -55℃～+105℃, total resistance value variation: ≤± 5％, No mechanical damage.

Exposure at low temperature

24 hours at -55℃, Total resistance value variation: ≤±5％, No mechanical damage.

Exposure at high temperature

1,000 hours at 105℃, Total resistance value variation: ≤±5％, No mechanical damage.

Vibration

10Hz～2000Hz, 147m/s², 12 hours, Total resistance value variation: ≤±5％, No mechanical and electrical damage.

Shock

490m/s², 11ms, 18 times, Total resistance value variation: ≤±1％, No mechanical and electrical damage.

Moisture resistance

40℃, 95％RH, 240 hours, Total resistance value variation: ≤±10％,Insulation resistance: ≥10MΩ.

Resistance temperature coefficient

±20p.p.m./°C

Standard turns

5 Turns；10Turns

Standard resistance range

100Ω~20kΩ；100Ω~50kΩ

Max. practical resistance value

50kΩ；100kΩ

Total resistance tolerance

Standard class ±3%(H)，Precision class ±1%(F)

Independent linearity tolerance

Standard class±0.35%，±0.25%；Precision class ±0.2%，±0.1%； (≤5kΩ) (±0.25%)，(±0.15%)

Electrical travel

360°×n±5° (n： Number of turns)

Power rating

0.75W；1.5W

Insulation resistance

≥1000MΩ (500V.D.C.)

Dielectric strength

1000V.A.C./1 min

Noise

≤100ΩE.N.R.

Standard resistance values (Ω)

100；200；500；1k；2k；5k；10k；20k；50k；100k

Number of wire turns 5Turns

920；1,190 ；1,250 ；1,510 ；1,790 ；2,380；3,120 ；3,800； 5,430 ；-

Number of wire turns 10 Turns

1,690 ；1,850； 2,560 ；2,500 ；3,030 ；4,170； 4,760； 6,250 ；8,330；※10870

Resistance wire used

Cu-Ni；Ni-Cr

Special shaft type

Shaft with front and rear extension (Rear shaft with 0.8mm dia. and 10mm length), special machining on the shaft

Speical turns

3 Turns（S12HP-3）

Speical protection grade (IP)

IP54 Simple sealed housing (In the case of servomount type, the housing length becomes longer by 1.2mm)