Mechanical travel

360°×n (n:Number of turns)

Protection grade (IP)

IP40

Starting torque

Bushingmount type：≤8mN·m (80gf·cm) ;Servomount type：≤5mN·m (50gf·cm)

Stopper strength

Approx. 0.9N•m (9kgf•cm)

Rotational life expectancy

25℃，No load at 40r.p.m;3Turns ——600,000 shaft revolutions;5 Turns——1,000,000 shaft revolutions;10,15,20 Turns——2,000,000 shaft revolutions;Total resistance value variation:≤± 5％ against initial value;Independent Iinearity tolerance:≤150％ of specified value;Noise: ≤500Ω E.N.R.

Mass

Approx. 50g (5 Turns), Approx. 60g (10 Turns)

Operating temperature range

-55℃～+105℃

Temperature cycle

5 cycles under -55℃～+105℃, total resistance value variation: ≤± 5％, No mechanical damage.

Exposure at low temperature

24 hours at -55℃, Total resistance value variation: ≤±5％, No mechanical damage.

Exposure at high temperature

1,000 hours at 105℃, Total resistance value variation: ≤±5％, No mechanical damage.

Vibration

10Hz～2000Hz, 147m/s², 12 hours, Total resistance value variation: ≤±5％, No mechanical and electrical damage.

Shock

490m/s², 11ms, 18 times, Total resistance value variation: ≤±1％, No mechanical and electrical damage.

Moisture resistance

40℃, 95％RH, 240 hours, Total resistance value variation: ≤±10％,Insulation resistance: ≥10MΩ.

Resistance temperature coefficient

±20p.p.m./°C

Standard turns

5 Turns;10 Turns

Standard resistance range

100Ω~50kΩ;100Ω~100kΩ

Max. practical resistance value

100kΩ;200kΩ

Total resistance tolerance

Standard class ±3%(H)，Precision class ±1%(F)

Independent linearity tolerance Standard class

±0.3%;±0.2%

Independent linearity tolerance Precision class

±0.2%;±0.1%

Independent linearity tolerance (≤5kΩ)

(±0.25%);(±0.15%)

Electrical travel

360°×n±5° (n:Number of turns)

Power rating

1.5W;2.0W

Insulation resistance

≥100MΩ (1000V.D.C.)

Dielectric strength

1000V.A.C./1 min

Noise

≤100ΩE.N.R.

Standard resistance values (Ω)

100;200;500;1k;2k;5k;10k;20k;50k;100k;200k

Number of wire turns 5 Turns

1,300;1,700;2,000;2,400 ;2,500;3,200;4,000;5,000;7,000;※8800;-

Number of wire turns 10 Turns

2,000;2,600;3,100;4,000;4,800;5,000;6,500;8,000 ;10,000 ;14,000 ;※18000

Resistance wire used

Cu-Ni; Ni-Cr

Special shaft type

Shaft with front and rear extension (Rear shaft with 3mm dia. and 10mm length), shaft dia. (φ3.175mm, φ6.35mm) & bushing with inch dimension, special machining on the shaft

Speical turns

3 Turns（S25HP-3）, 15 Turns（S25HP-15）, 20 Turns（S25HP-20）

Lower resistance

10Ω, 20Ω, 50Ω

Extra tap

Extra taps (Available up to 5 taps)

Multi-ganged

Up to 2 gangs

Speical protection grade (IP)

IP54